DIY Plus Tape Socket - Revision history

Bryce at 14:22, 31 January 2011

2011-01-31T14:22:21Z

← Older revision		Revision as of 14:22, 31 January 2011
Line 13:		Line 13:

	[[Image:6128_Plus_Tape_Socket.JPG\|600px\|centre]]		[[Image:6128_Plus_Tape_Socket.JPG\|600px\|centre]]


			If you're getting errors while trying to load or save files, you can find the error code descriptions here: [[Read_error_codes\|Read Error Codes]]

	[[Category:Peripherals]] [[Category:DIY]][[Category:DATA Storage]][[Category:CPC Plus]]		[[Category:Peripherals]] [[Category:DIY]][[Category:DATA Storage]][[Category:CPC Plus]]

MacDeath at 18:53, 19 December 2010

2010-12-19T18:53:40Z

← Older revision		Revision as of 18:53, 19 December 2010
Line 14:		Line 14:
	[[Image:6128_Plus_Tape_Socket.JPG\|600px\|centre]]		[[Image:6128_Plus_Tape_Socket.JPG\|600px\|centre]]

	[[Category:~~Hardware~~]] [[Category:~~Peripherals~~]] [[Category:~~DIY~~]][[Category:~~DATA Storage~~]]		[[Category:Peripherals]] [[Category:DIY]][[Category:DATA Storage]][[Category:CPC Plus]]

TheRogue at 08:34, 15 March 2010

2010-03-15T08:34:12Z

← Older revision		Revision as of 08:34, 15 March 2010
Line 5:		Line 5:
	The header connector CP07 can be found in the bottom right corner of the main PCB. Ensure that the relay and diode are mounted in such a way that none of their pins can come in contact with any metal within the CPC housing or any other part of the main PCB.		The header connector CP07 can be found in the bottom right corner of the main PCB. Ensure that the relay and diode are mounted in such a way that none of their pins can come in contact with any metal within the CPC housing or any other part of the main PCB.

	The transistor and ~~diode~~ shown in red below, must be added to the main PCB, the pad positions should be present but unpopulated.		The transistor and resistor shown in red below, must be added to the main PCB, the pad positions should be present but unpopulated.

	Note: The pinout of the 2N3904 is not identical to the original transistor used by Amstrad and should be mounted as shown below with the Base and Collector pins swapped!		Note: The pinout of the 2N3904 is not identical to the original transistor used by Amstrad and should be mounted as shown below with the Base and Collector pins swapped!

MacDeath at 13:03, 9 February 2010

2010-02-09T13:03:41Z

← Older revision		Revision as of 13:03, 9 February 2010
Line 14:		Line 14:
	[[Image:6128_Plus_Tape_Socket.JPG\|600px\|centre]]		[[Image:6128_Plus_Tape_Socket.JPG\|600px\|centre]]

	[[Category:Hardware]] [[Category:Peripherals]] [[Category:DIY]]		[[Category:Hardware]] [[Category:Peripherals]] [[Category:DIY]][[Category:DATA Storage]]

Bryce at 12:21, 9 February 2010

2010-02-09T12:21:50Z

← Older revision		Revision as of 12:21, 9 February 2010
Line 7:		Line 7:
	The transistor and diode shown in red below, must be added to the main PCB, the pad positions should be present but unpopulated.		The transistor and diode shown in red below, must be added to the main PCB, the pad positions should be present but unpopulated.

	The pinout of the 2N3904 is identical to the original transistor used by Amstrad and should be mounted as shown below.		Note: The pinout of the 2N3904 is not identical to the original transistor used by Amstrad and should be mounted as shown below with the Base and Collector pins swapped!

			Should you be able to source the original transistor (now sold as 2SC1815) these pins should not be swapped.

Bryce at 12:00, 9 February 2010

2010-02-09T12:00:18Z

← Older revision		Revision as of 12:00, 9 February 2010
Line 4:		Line 4:

	The header connector CP07 can be found in the bottom right corner of the main PCB. Ensure that the relay and diode are mounted in such a way that none of their pins can come in contact with any metal within the CPC housing or any other part of the main PCB.		The header connector CP07 can be found in the bottom right corner of the main PCB. Ensure that the relay and diode are mounted in such a way that none of their pins can come in contact with any metal within the CPC housing or any other part of the main PCB.

			The transistor and diode shown in red below, must be added to the main PCB, the pad positions should be present but unpopulated.

	The pinout of the 2N3904 is identical to the original transistor used by Amstrad and should be mounted as shown below.		The pinout of the 2N3904 is identical to the original transistor used by Amstrad and should be mounted as shown below.

Bryce: Created page with '== Description == The connection diagram below will allow you to connect a tape player or other audio recording device / PC soundcard to a CPC6128+ which will then act as a Tape…'

2010-02-09T11:57:34Z

Created page with '== Description == The connection diagram below will allow you to connect a tape player or other audio recording device / PC soundcard to a CPC6128+ which will then act as a Tape…'

New page

== Description ==

The connection diagram below will allow you to connect a tape player or other audio recording device / PC soundcard to a CPC6128+ which will then act as a Tape input and output.

The header connector CP07 can be found in the bottom right corner of the main PCB. Ensure that the relay and diode are mounted in such a way that none of their pins can come in contact with any metal within the CPC housing or any other part of the main PCB.

The pinout of the 2N3904 is identical to the original transistor used by Amstrad and should be mounted as shown below.

[[Image:6128_Plus_Tape_Socket.JPG|600px|centre]]

[[Category:Hardware]] [[Category:Peripherals]] [[Category:DIY]]